Polyaspartic Urethane ®

 

BENEFITS:

  • Optional Anti-Microbial® additive

  • Excellent gloss retention

  • Excellent chemical resistance

  • Excellent abrasion resistance

  • Complete UV resistance

  • Thermal-shock resistant

  • Qualified LEED® product

RECOMMENDED USES: 

 

Polyaspartic is versatile as a binder or grout and seal coat. Its most popular use is as a grout and seal coat for DiamondCast® and Diamond-Crete systems, providing complete UV resistance, increased chemical resistance, and added abrasion resistance, in an aesthetically pleasing finish.

TYPICAL PROPERTIES:

 

Compressive Strength (ASTM C-579)..........19,200 psi

Hardness (Shore D) (ASTM D-2240)...................70–75

Bond Strength (ASTM D-4541)..........................400 psi

Abrasion Resistance (ASTM D-4060)..................35 mg

Volume Solids.......................................................100%

VOC...................................................................0 gm/ltr

Pot Life at 77° F.................................................20 mins

Return to service at 77° F....................................12 hrs

Full cure at 77° F.................................................24 hrs

 

NOTE: During application, installer must maintain a wet edge in order to avoid carbon dioxide bubbles from overlapping.

The data shown above reflect typical results based on laboratory testing under controlled conditions. Reasonable variations from the data shown above may result.

 

SHELF LIFE: 12 months from date of purchase @77° F


CHEMICAL RESISTANCE: 

See Chemical Resistance Guide for all DiamondStone products. 

CLEANING AND MAINTENANCE: 

Refer to DiamondStone cleaning and maintenance instructions.

PRECAUTIONS: 

 

DiamondStone, LLC recommends the use of slip-resistant grit with this product. Floors should be sloped to drain to prevent standing water or chemicals. As with any surface, all spills should be removed as soon as possible to prevent a slipping hazard. Always use protective clothing, gloves and goggles consistent with OSHA regulations during use. Avoid eye and skin contact. Do not ingest or inhale. Refer to Material Safety Data Sheet for detailed safety precautions.

DESCRIPTION: 

 

POLYASPARTIC is a plural-component, moisture cured aliphatic polyurea utilized as a topcoat on many DiamondStone® systems. It provides excellent durability to the system while adding complete UV resistance and excellent abrasion resistance. What makes this product unique is that is has zero VOCs. When used as a topcoat over Diamond-Crete® flooring systems, Polyaspartic 100 provides thermal-shock and thermal-cycling resistance consistent with Diamond-Crete flooring systems.

SURFACE PREPARATION: 

 

Apply only to clean and sound concrete substrates that are free of all coatings, sealers, curing compounds, oils, greases or any other contaminants. New concrete should be cured a minimum of 28 days. Concrete that has been contaminated with chemicals or other foreign matter must be neutralized or removed. Remove any laitance or weak surface layers. Concrete should have a minimum surface ten-sile strength of 300 psi. Prepare surface by mechanical means to achieve a profile equal to industry standards. Moisture testing of the concrete surface should be performed pursuant to ASTM E-1907 moisture testing specification. See DiamondStone Concrete Moisture Limits & Testing Policy for project-specific testing requirements and, if neces sary, moisture-tolerant options. Bare concrete should be tested for pH and exhibit a pH between 7 and 11. NOTE: Although testing is critical, it is not a guarantee that future challenges will not arise. All surface irregu-larities, cracks, expansion joints and control joints should be properly addressed prior to application. Outgassing may occur due to the porosity of some concrete surfaces. Refer to DiamondStone Surface Preparation Guidelines for more details. 

LIMITATIONS: 

 

Do not apply when concrete temperatures are less than 50º F or greater than 85º F. (Material cures slower at cooler temperatures,

and working time will be substantially reduced at higher temperatures.) All components should be stored in a dry place at temp -eratures between 65° F and 85° F. Confirm product performance in specific chemical environment prior to use. Installation temperature should be above 40°F. Actual color may vary slightly upon application.

 

WARRANTY INFORMATION: 


DiamondStone, LLC warrants its products to be free from defects in material and workmanship. DiamondStone, LLC’s sole obligation and Buyer’s exclusive remedy in connection with the products shall be limited, at DiamondStone, LLC’s option, to either replacement of products not conforming to this warranty or credit to Buyer’s account in the invoiced amount of the nonconforming products. Any claim under this warranty must be made by Buyer to DiamondStone, LLC in writing within five (5) days of Buyer’s discovery of the claimed defect, but in no event later than the expiration of the applicable shelf life, or one (1) year from the delivery date, whichever is earlier. Buyer’s failure to notify DiamondStone, LLC of such nonconformance as required herein shall bar Buyer from recovery under this warranty.

This Limited Warranty is exclusive and in lieu of all other warranties of any kind or nature whatsoever. DiamondStone, LLC makes no other warranties concerning this product. No other warranties, whether expressed, implied or statutory, shall apply. All other warranties, including, but not limited to, implied warranties of good performance, merchantability and fitness for particular purpose are hereby excluded and disclaimed. In no event shall DiamondStone, LLC be liable for consequential or incidental damages.

Any recommendation or suggestion relating to the use of the products made by DiamondStone, LLC, whether in its technical literature, in response to specific inquiry, or otherwise, is based on data believed to be reliable; however, the products and information are intended for use by Buyers having requisite skill and know-how in the industry, and therefore it is for the Buyer to satisfy itself of the suitability of the products for its own particular use, and it shall be deemed that Buyer has done so, at its sole discretion and risk. Variation in environment, changes in procedures of use, or extrapolation of data may cause unsatisfactory results. DiamondStone, LLC cannot guarantee that color will conform to sample, if provided.

Toll Free: 888-817-8663

info@diamondstoneproducts.com

 

©2017 DiamondStone, LLC. All Rights Reserved.