Diamond-Metallic®

 

DESCRIPTION: 

 

DIAMOND-METALLIC is a 100%-solids decorative topping designed for both durability and beauty. Diamond-Metallic uses metallic particles blended into the polymer resin. A liquid dispersing agent can be spray-applied to the wet flooring to distress the metallic particles, producing a decorative and variegated finish. Diamond-Metallic can be topcoated with a wide variety of DiamondStone® urethane topcoats, depending upon the texture and finish desired.

BENEFITS:

  • Engineered with stress-relieving flexibility

  • Low-odor formula

  • 100% solids; no VOCs 

  • No extending fillers or diluents

  • Seamless, monolithic application

  • Slip resistant, with the addition of OX-Grit

  • UV resistant

  • Aesthetically unique

  • Qualified LEED® product

TYPICAL PROPERTIES:

 

Compressive Strength (ASTM D-695-85).....11,000 psi

Tensile Strength (ASTM D-638-86)...............10,000 psi

Flexural Strength (ASTM D-790-86)..............19,500 psi

Hardness (Shore D) (ASTM D-2240).........................88

Bond Strength (ASTM D-4541)..........................500 psi

Abrasion Resistance (ASTM D-4060)................18 mg*

Pot Life at 77º F.................................................32 mins

Foot Traffic at 77º F........................................10–12 hrs

Full Service at 77º F.............................................24 hrs

 

The data shown above reflect typical results based on laboratory testing under controlled conditions. Reasonable variations from the data shown above may result.

RECOMMENDED USES: 

 

Diamond-Metallic is well-suited for floor surfaces where a highly decorative and unique aesthetic appeal is desired. Typical installations include automotive showrooms, commercial offices, retail space and sporting venues.

LIMITATIONS: 

 

Floors should be sloped to drain to prevent standing water or chemicals. As with any surface, all spills should be removed as soon as possible to prevent a slipping hazard. Confirm product performance in specific chemical environment prior to use. Prepare substrate according to “Surface Preparation” portion of this document. Diamond-Metallic is an artistic product; no two floors are the same. Application of the distressing agent will create varying results that are beyond the applicator’s control. 

PRECAUTIONS: 

 

Always use protective clothing, gloves and goggles consistent with OSHA regulations during use. Avoid eye and skin contact. Do not ingest or inhale. Refer to Material Safety Data Sheet for detailed safety precautions. 

ADDITIONAL SLIP RESISTANCE AVAILABLE: 
 

 

OX-Grit 60*

Light......................................1 lb/1,000 square foot

Medium...............................2 lbs/1,000 square foot

Heavy..................................3 lbs/1,000 square foot

 

 

OX-Grit 30

Light............................... 2–3 lbs/1,000 square foot

Medium...........................4–6 lbs/1,000 square foot

Heavy............................7–10 lbs/1,000 square foot

 

*For use in urethane topcoats only 

CHEMICAL RESISTANCE: 

See Chemical Resistance Guide for all DiamondStone products. 

CLEANING AND MAINTENANCE: 

Refer to DiamondStone cleaning and maintenance instructions.

SURFACE PREPARATION: 

 

Apply only to clean and sound concrete substrates that are free of all coatings, sealers, curing compounds, oils, greases or any other contaminants. New concrete should be cured a minimum of 28 days. Concrete that has been contaminated with chemicals or other foreign matter must be neutralized or removed. Remove any laitance or weak surface layers. Concrete should have a minimum surface tensile strength of 300 psi. Prepare surface by mechanical means to achieve a profile equal to industry standards. Moisture testing of the concrete surface should be performed pursuant to ASTM E-1907 moisture testing specification. See DiamondStone Concrete Moisture Limits & Testing Policy for project-specific testing requirements and, if necessary, moisture-tolerant options. Bare concrete should be tested for pH and exhibit a pH between 7 and 11. NOTE: Although testing is critical, it is not a guarantee that future challenges will not arise. All surface irregularities, cracks, expansion joints and control joints should be properly addressed prior to application. Outgassing may occur due to the porosity of some concrete surfaces. Refer to DiamondStone Surface Preparation Guidelines for more details.

 

WARRANTY INFORMATION: 


DiamondStone, LLC warrants its products to be free from defects in material and workmanship. DiamondStone, LLC’s sole obligation and Buyer’s exclusive remedy in connection with the products shall be limited, at DiamondStone, LLC’s option, to either replacement of products not conforming to this warranty or credit to Buyer’s account in the invoiced amount of the nonconforming products. Any claim under this warranty must be made by Buyer to DiamondStone, LLC in writing within five (5) days of Buyer’s discovery of the claimed defect, but in no event later than the expiration of the applicable shelf life, or one (1) year from the delivery date, whichever is earlier. Buyer’s failure to notify DiamondStone, LLC of such nonconformance as required herein shall bar Buyer from recovery under this warranty.

This Limited Warranty is exclusive and in lieu of all other warranties of any kind or nature whatsoever. DiamondStone, LLC makes no other warranties concerning this product. No other warranties, whether expressed, implied or statutory, shall apply. All other warranties, including, but not limited to, implied warranties of good performance, merchantability and fitness for particular purpose are hereby excluded and disclaimed. In no event shall DiamondStone, LLC be liable for consequential or incidental damages.

Any recommendation or suggestion relating to the use of the products made by DiamondStone, LLC, whether in its technical literature, in response to specific inquiry, or otherwise, is based on data believed to be reliable; however, the products and information are intended for use by Buyers having requisite skill and know-how in the industry, and therefore it is for the Buyer to satisfy itself of the suitability of the products for its own particular use, and it shall be deemed that Buyer has done so, at its sole discretion and risk. Variation in environment, changes in procedures of use, or extrapolation of data may cause unsatisfactory results. DiamondStone, LLC cannot guarantee that color will conform to sample, if provided.

Toll Free: 888-817-8663

info@diamondstoneproducts.com

 

©2017 DiamondStone, LLC. All Rights Reserved.