DiamondCast Novolac System®
DIAMONDCAST NOVOLAC SYSTEM is a multifunctional polymer coating formulated to provide maximum chemical resistance to 98% sulfuric acid and other aggressive chemicals. DiamondCast Novolac System provides excellent durability due in part to the microfibers incorporated into the resin that act as stress relievers, enabling the floor to relax after an incident. This resilience provides excellent scratch resistance.
IMPACT RESISTANCE: DiamondCast Novolac System uses a proprietary grinding process during installation. This process densifies the floor, raising compressive strength and providing outstanding impact resistance.
CHEMICAL RESISTANCE: DiamondCast Novolac System has excellent chemical resistance to aggressive acids, including 98% sulfuric. Refer to DiamondStone Chemical Resistance Guide for specific chemical and concentration resistance.
ABRASION RESISTANCE: DiamondCast Novolac System provides excellent abrasion resistance in a novolac coating.
LEED® QUALIFIED PRODUCT: DiamondCast Novolac System meets the requirements to be considered a LEED-accredited product as defined by the U.S. Green Building Council.
Compressive Strength (ASTM C-579).....19,000 psi
Tensile Strength (ASTM C-307)...............12,000 psi
Flexural Strength (ASTM C-580)...............4,000 psi
Hardness (Shore D) (ASTM D-2240)..............70–75
Bond Strength (ASTM D-4541)....................425 psi
Abrasion Resistance (ASTM D-4060)...........35 mg*
Pot Life at 77° F...........................................20 mins
Foot Traffic at 77° F....................................8–10 hrs
Full Service at 77° F.......................................24 hrs
*When using Polyaspartic Urethane as the finish coat
The data shown above reflect typical results based on laboratory testing under controlled conditions. Reasonable variations from the data shown above may result.
DiamondCast Novolac System is formulated specifically to resist direct contact with most inorganic acids such as 98% sulfuric acid, phosphoric acid and hydrochloric acid. Because of its compatibility with concrete, it is ideal for process-area floors, secondary containment and truck loading/unloading areas. DiamondCast Novolac System is also recommended for pump pads, pedestals, curbs, dike walls and battery charging areas. DiamondCast Novolac System provides excellent thermal compatibility with concrete when compared with conventional coatings.
Apply only to clean and sound concrete substrates that are free of all coatings, sealers, curing compounds, oils, greases or any other contaminants. New concrete should be cured a minimum of 28 days. Concrete that has been contaminated with chemicals or other foreign matter must be neutralized or removed. Remove any laitance or weak surface layers. Concrete should have a minimum surface tensile strength of 300 psi. Prepare surface by mechanical means to achieve a profile equal to industry standards. Moisture testing of the concrete surface should be performed pursuant to ASTM E-1907 moisture testing specification. See DiamondStone Concrete Moisture Limits & Testing Policy for project-specific testing requirements and, if necessary, moisture-tolerant options. Bare concrete should be tested for pH and exhibit a pH between 7 and 11. NOTE: Although testing is critical, it is not a guarantee that future challenges will not arise. All surface irregularities, cracks, expansion joints and control joints should be properly addressed prior to application. Outgassing may occur due to the porosity of some concrete surfaces. Refer to DiamondStone Surface Preparation Guidelines for more details.
Always use protective clothing, gloves and goggles consistent with OSHA regulations during use. Avoid eye and skin contact. Do not ingest or inhale. Refer to Material Safety Data Sheet for detailed safety precautions.
ADDITIONAL SLIP RESISTANCE:
Is available with the addition of OX-Grit 30
See Chemical Resistance Guide for all DiamondStone products.
CLEANING AND MAINTENANCE:
Refer to DiamondStone cleaning and maintenance instructions.
DiamondStone, LLC warrants its products to be free from defects in material and workmanship. DiamondStone, LLC’s sole obligation and Buyer’s exclusive remedy in connection with the products shall be limited, at DiamondStone, LLC’s option, to either replacement of products not conforming to this warranty or credit to Buyer’s account in the invoiced amount of the nonconforming products. Any claim under this warranty must be made by Buyer to DiamondStone, LLC in writing within five (5) days of Buyer’s discovery of the claimed defect, but in no event later than the expiration of the applicable shelf life, or one (1) year from the delivery date, whichever is earlier. Buyer’s failure to notify DiamondStone, LLC of such nonconformance as required herein shall bar Buyer from recovery under this warranty.
This Limited Warranty is exclusive and in lieu of all other warranties of any kind or nature whatsoever. DiamondStone, LLC makes no other warranties concerning this product. No other warranties, whether expressed, implied or statutory, shall apply. All other warranties, including, but not limited to, implied warranties of good performance, merchantability and fitness for particular purpose are hereby excluded and disclaimed. In no event shall DiamondStone, LLC be liable for consequential or incidental damages.
Any recommendation or suggestion relating to the use of the products made by DiamondStone, LLC, whether in its technical literature, in response to specific inquiry, or otherwise, is based on data believed to be reliable; however, the products and information are intended for use by Buyers having requisite skill and know-how in the industry, and therefore it is for the Buyer to satisfy itself of the suitability of the products for its own particular use, and it shall be deemed that Buyer has done so, at its sole discretion and risk. Variation in environment, changes in procedures of use, or extrapolation of data may cause unsatisfactory results. DiamondStone, LLC cannot guarantee that color will conform to sample, if provided.