High Traffic Topcoat®

 

BENEFITS:

  • Low-odor formula

  • Excellent chemical resistance

  • Excellent abrasion resistance

  • Excellent UV resistance

  • Excellent color retention

  • 250–300% increased light reflection

  • Built-in slip resistance

  • Qualified LEED® product

 

RECOMMENDED USES: 

 

High-Traffic Topcoat offers outstanding wear resistance and durability, lasting up to four times longer than standard epoxies. High-Traffic Topcoat incorporates an environmentally friendly formula that, unlike conventional solvent-based polyurethane coatings, gives off little odor during application. This feature is a significant benefit for installations inside areas where occupants are present.  Typical uses are as finish coats over DiamondStone

TYPICAL PROPERTIES:

 

Volume Solids.........................................................95%

VOC.................................................................72 gm/ltr

Abrasion Resistance (ASTM D-4060)*.........18 mg/loss

Coefficient of Friction (ASTM D-4518).......................70

Pot Life at 77° F.................................................45 mins

Tack-Free at 77° F.................................................6 hrs

Full Service at 77° F.............................................24 hrs

 

 

*1,000 cycles using CS-17 wheel, 1,000 gm load 

The data shown above reflect typical results based on laboratory testing under controlled conditions. Reasonable variations from the data shown above may result.

SHELF LIFE: 6 months at 77° F 


CHEMICAL RESISTANCE: 

See Chemical Resistance Guide for all DiamondStone products. 

CLEANING AND MAINTENANCE: 

Refer to DiamondStone cleaning and maintenance instructions.

PRECAUTIONS: 

 

For industrial and commercial use only. Must be applied by trained personnel only. Do not use lacquer thinners or solvents containing alcohol as thinners. Not for immersion service. Do not apply where ambient operating temperatures exceed 150° F or application temperatures are below 50° F or above 95° F. Do not apply to wet or damp substrates. Do not use on concrete floors with membranes or sealers unless properly removed. Vehicles with rubber tires should not be parked on coating within 36 hours of installation. Floors should be sloped to drain to prevent standing water or chemicals. As with any surface, all spills should be removed as soon as possible to prevent a slipping hazard. Always wear protective clothing, gloves and goggles during use. Do not use in an unventilated area. Please refer to the Material Safety Data Sheet for detailed safety precautions. 

DESCRIPTION: 

 

HIGH-TRAFFIC TOPCOAT is a high-performance, 95%-solids, aliphatic, moisture-cured urethane with unsurpassed wear resistance. It offers excellent long-term durability, color retention and UV resistance, along with excellent chemical resistance to most solvents found in manufacturing and industrial areas. High-Traffic Topcoat is an ideal choice for areas with heavy traffic.  

SURFACE PREPARATION: 

 

Apply only to clean and sound concrete substrates that are free of all coatings, sealers, curing compounds, oils, greases or any other contaminants. New concrete should be cured a minimum of 28 days. Concrete that has been contaminated with chemicals or other foreign matter must be neutralized or removed. Remove any laitance or weak surface layers. Concrete should have a minimum surface tensile strength of 300 psi. Prepare surface by mechanical means to achieve a profile equal to industry standards. Moisture testing of the concrete surface should be performed pursuant to ASTM E-1907 moisture testing specification. See DiamondStone Concrete Moisture Limits & Testing Policy for project-specific testing requirements and, if necessary, moisture-tolerant options. Bare concrete should be tested for pH and exhibit a pH between 7 and 11. NOTE: Although testing is critical, it is not a guarantee that future challenges will not arise. All surface irregularities, cracks, expansion joints and control joints should be properly addressed prior to application. Outgassing may occur due to the porosity of some concrete surfaces. Refer to DiamondStone Surface Preparation Guidelines for more details. 

LIMITATIONS: 

 

Do not apply when concrete temperatures are less than 50° F or greater than 85° F. (Material cures slower at cooler temperatures, and working time will be substantially reduced at higher temperatures.) Severe roller marking can occur at higher temperatures. All components should be stored in a dry place at temperatures between 65° F and 85° F. Confirm product performance in specific chemical environment prior to use. Substrate temperature must be at least 5° F above the dew point. Actual color may vary slightly upon application. Material can exhibit roller marks depending upon temperature, humidity and width of area coated. As floor wears in, roller marks dissipate. 

epoxy flooring systems, in a wide variety of indoor or outdoor industrial and commercial applications, including store aisles, corridors, tunnels, airplane hangars, and manufacturing areas. 

 

WARRANTY INFORMATION: 


DiamondStone, LLC warrants its products to be free from defects in material and workmanship. DiamondStone, LLC’s sole obligation and Buyer’s exclusive remedy in connection with the products shall be limited, at DiamondStone, LLC’s option, to either replacement of products not conforming to this warranty or credit to Buyer’s account in the invoiced amount of the nonconforming products. Any claim under this warranty must be made by Buyer to DiamondStone, LLC in writing within five (5) days of Buyer’s discovery of the claimed defect, but in no event later than the expiration of the applicable shelf life, or one (1) year from the delivery date, whichever is earlier. Buyer’s failure to notify DiamondStone, LLC of such nonconformance as required herein shall bar Buyer from recovery under this warranty.

This Limited Warranty is exclusive and in lieu of all other warranties of any kind or nature whatsoever. DiamondStone, LLC makes no other warranties concerning this product. No other warranties, whether expressed, implied or statutory, shall apply. All other warranties, including, but not limited to, implied warranties of good performance, merchantability and fitness for particular purpose are hereby excluded and disclaimed. In no event shall DiamondStone, LLC be liable for consequential or incidental damages.

Any recommendation or suggestion relating to the use of the products made by DiamondStone, LLC, whether in its technical literature, in response to specific inquiry, or otherwise, is based on data believed to be reliable; however, the products and information are intended for use by Buyers having requisite skill and know-how in the industry, and therefore it is for the Buyer to satisfy itself of the suitability of the products for its own particular use, and it shall be deemed that Buyer has done so, at its sole discretion and risk. Variation in environment, changes in procedures of use, or extrapolation of data may cause unsatisfactory results. DiamondStone, LLC cannot guarantee that color will conform to sample, if provided.

Toll Free: 888-817-8663

info@diamondstoneproducts.com

 

©2017 DiamondStone, LLC. All Rights Reserved.