SlurryStone ESD®

 

DESCRIPTION: 

 

SLURRYSTONE ESD is a 100% solids epoxy static-dissipative system that hardens to an attractive, durable finish. SlurryStone ESD offers the most consistent protection within the ESD range through the use of particulate technology and is backed by a 10-year limited warranty on electrical properties. This material is also available in a Novolac version for increased chemical resistance.

BENEFITS:

  • 100% solids; no VOCs

  • Excellent self-leveling properties

  • UV resistant

  • Smooth, high-gloss surface

  • Resists many acids and solvents

  • 10-year limited warranty

  • Particulate technology

  • Qualified LEED® product

TYPICAL PROPERTIES: 
 

Compressive Strength (ASTM C-579).................13,500 psi

Tensile Strength – Resin Only (ASTM C-307).......8,000 psi

Flexural Strength (ASTM C-580)...........................2,325 psi

Abrasion Resistance (ASTM D-4060)................80 mg/loss

Hardness (Shore D) (ASTM D-2240).........................50–80

Indentation at 2,000 lbs...............................................none

Slip Coefficient............................................................0.507

Rate of Burning........................................self-extinguishing

Linear Thermal Expansion...........................................none

Water Absorption..........................................................03%

Elongation............................................................(70) 3.5%

 

The data shown above reflect typical results based on laboratory testing under controlled conditions. Reasonable variations from the data shown above may result.

 

ELECTRICAL RESISTANCE: 


Surface-to-ground: 1 meg ohm to 1 gig ohm, commonly known as 1x106 to 1x109

 

RECOMMENDED USES: 

 

SlurryStone ESD is recommended anywhere a static protective flooring system is required. Combined with personnel and workstation grounding, it results in an integrated static-control program that offers maximum protection against static damage. 

LIMITATIONS: 

 

Do not apply when concrete temperatures are less than 50º F or greater than 95º F. (Material cures slower at cooler temperatures, and working time will be substantially reduced at higher temperatures.) All components should be stored in a dry place at temperatures between 65º F and 85º F. Confirm product performance in specific chemical environment prior to use. Substrate temperature must be at least 5º F above the dew point.

SURFACE PREPARATION: 

 

Apply only to clean and sound concrete substrates that are free of all coatings, sealers, curing compounds, oils, greases or any other contaminants. New concrete should be cured a minimum of 28 days. Concrete that has been contaminated with chemicals or other foreign matter must be neutralized or removed. Remove any laitance or weak surface layers. Concrete should have a minimum surface tensile strength of 300 psi. Prepare surface by mechanical means to achieve a profile equal to industry standards. Moisture testing of the concrete surface should be performed pursuant to ASTM E-1907 moisture testing specification. See Diamond-Stone Concrete Moisture Limits & Testing Policy for project-specific testing requirements and, if necessary, moisture-tolerant options. Bare concrete should be tested for pH and exhibit a pH between 7 and 11. NOTE: Although testing is critical, it is not a guarantee that future challenges will not arise. All surface irregularities, cracks, expansion joints and control joints should be properly addressed prior to application. Outgassing may occur due to the porosity of some concrete surfaces. Refer to DiamondStone Surface Preparation Guidelines for more details. 

CHEMICAL RESISTANCE: 

See Chemical Resistance Guide for all DiamondStone products. 

 

CLEANING AND MAINTENANCE: 


Install entrance matting at all room entry doors to prevent debris from being tracked onto the ESD epoxy floor. Never apply wax to static-dissipative or conductive epoxy flooring! Sweep or dry-mop daily with an untreated dust mop. Damp-mop as needed. For normal dirt, grime and scuff marks, apply a neutral pH cleaner with a mop and then scrub with a low-speed “swing” buffer and a white buffer pad. Wipe up the soiled solution with a damp mop. Damp-mop again with clean solution, and allow the floor to dry completely. To remove more difficult marks, follow the same procedure using a tan buffer pad. Never use abrasive pads, brushes or stripping pads on an ESD epoxy floor. They will damage the surface gloss of the floor. Use only white or tan buffer pads in accordance with DiamondStone maintenance instructions

 

WARRANTY INFORMATION: 


DiamondStone, LLC warrants its products to be free from defects in material and workmanship. DiamondStone, LLC’s sole obligation and Buyer’s exclusive remedy in connection with the products shall be limited, at DiamondStone, LLC’s option, to either replacement of products not conforming to this warranty or credit to Buyer’s account in the invoiced amount of the nonconforming products. Any claim under this warranty must be made by Buyer to DiamondStone, LLC in writing within five (5) days of Buyer’s discovery of the claimed defect, but in no event later than the expiration of the applicable shelf life, or one (1) year from the delivery date, whichever is earlier. Buyer’s failure to notify DiamondStone, LLC of such nonconformance as required herein shall bar Buyer from recovery under this warranty.

This Limited Warranty is exclusive and in lieu of all other warranties of any kind or nature whatsoever. DiamondStone, LLC makes no other warranties concerning this product. No other warranties, whether expressed, implied or statutory, shall apply. All other warranties, including, but not limited to, implied warranties of good performance, merchantability and fitness for particular purpose are hereby excluded and disclaimed. In no event shall DiamondStone, LLC be liable for consequential or incidental damages.

Any recommendation or suggestion relating to the use of the products made by DiamondStone, LLC, whether in its technical literature, in response to specific inquiry, or otherwise, is based on data believed to be reliable; however, the products and information are intended for use by Buyers having requisite skill and know-how in the industry, and therefore it is for the Buyer to satisfy itself of the suitability of the products for its own particular use, and it shall be deemed that Buyer has done so, at its sole discretion and risk. Variation in environment, changes in procedures of use, or extrapolation of data may cause unsatisfactory results. DiamondStone, LLC cannot guarantee that color will conform to sample, if provided.

Toll Free: 888-817-8663

info@diamondstoneproducts.com

 

©2017 DiamondStone, LLC. All Rights Reserved.